EN Standard Hydraulic Hose &#; Spiral or Braid Reinforcement for Higher Pressure

EN standard hydraulic hose is another standard all over the world. It has different reinforcement structures, such as different braid or spiral layers to increase the pressure of hydraulic hose. Here are commonly used EN standard hydraulic hose, including structures, drawings, specs and applications.

For more information, please visit SANYEFLEX.

EN 853 1SN Steel Wire Reinforced Hydraulic Rubber Hose

Introduction

EN 853 1SN single wire braided hydraulic hose is mainly used in high pressure hydraulic systems. The difference between 1ST and 1SN is that the later type has thinner covers. So type 1SN is not suitable for applications that requires remove.

High tensile steel wire braid reinforcement provides high working pressure and ozone and weather resistant synthetic rubber cover protecting the inside reinforcement and tube from abrasion and corrosion. It is suitable for carrying fluids such as glycol, mineral oil, fuel, lubricants, emulsion, hydrocarbon etc.

ENHH-01: EN 853 1SN hydraulic hose drawing.

ENHH-02: EN 853 1SN hydraulic hose with one-braid high tensile steel wire reinforcement.

Construction

• Tube: high quality synthetic rubber compounds.
• Reinforcement: one-braid high tensile steel wire.
• Cover: abrasion and weather resistant synthetic rubber.
• Temperature: -40 °C to +100 °C (-40 °F to +212 °F).

Table 1: EN 853 1ST/1SN Steel Wire Reinforced Hydraulic Rubber Hose Technical Specification Item Size SAE Size I.D. Reinforcement W.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight A AT mm inch dash min. max. min. max. min. max. max. MPa psi MPa psi MPa psi mm kg/m ENS-01 5 3/16 -3 4.6 5.4 9.0 10.0 11.9 13.5 12.5 25 50 100 90 0.20 ENS-02 6.3 1/4 -4 6.2 7.0 10.6 11.6 15.1 16.7 14.1 22.5 45 90 100 0.25 ENS-03 8 5/16 -5 7.7 8.5 12.1 13.3 16.7 18.3 15.7 21.5 43 85 115 0.31 ENS-04 10 3/8 -6 9.3 10.1 14.5 15.7 19.0 20.6 18.1 18 36 72 130 0.36 ENS-05 12.5 1/2 -8 12.3 13.5 17.5 19.1 22.2 23.8 21.4 16 32 64 180 0.45 ENS-06 16 5/8 -10 15.5 16.7 20.6 22.2 25.4 27.0 24.5 13 26 52 200 0.52 ENS-07 19 3/4 -12 18.6 19.8 24.6 26.2 29.4 31.0 28.5 10.5 21 42 240 0.65 ENS-08 25 1 -16 25.0 26.4 32.5 34.1 37.1 39.1 36.6 8.8 17.5 35 300 0.91 ENS-09 31.5 1-1/4 -20 31.4 33.0 39.3 41.7 44.4 47.6 44.8 6.3 910 15 25 420 1.30 ENS-10 38 1-1/2 -24 37.7 39.3 45.6 48.0 50.8 54.0 52.1 5 725 10 20 500 1.70 ENS-11 51 2 -32 50.4 52.0 58.7 61.7 65.1 68.3 65.5 4 580 8 16 630 2.00

EN 853 2SN Steel Wire Reinforced Hydraulic Rubber Hose

Introduction

EN 853 2SN hydraulic rubber hose is reinforced by two-braid high tensile steel wires to support high working pressures &#; up to psi at 3/16" I.D.. Oil resistant tube and ozone & abrasion resistant cover contribute long-term service life. It is available to convey water based and petroleum based hydraulic fluids within -40°C to 100°C (max. 120 °C intermittent).

They are widely used in offshore, forestry, factories and similar applications where abrasion resistance requirements is strict.

ENHH-03: EN 853 2SN hydraulic hose drawing.

ENHH-04: EN 853 2SN hydraulic hose has two-braid high tensile steel wires.

Construction

• Tube: high quality synthetic rubber compounds.
• Reinforcement: two-braid high tensile steel wires.
• Cover: abrasion and weather resistant synthetic rubber.
• Temperature: -40 °C to +100 °C (-40 °F to +212 °F).

Table 2: EN 853 2ST/2SN Steel Wire Reinforced Hydraulic Rubber Hose Technical Specification Item Size SAE Size I.D. Reinforcement W.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight A AT mm inch dash min. max. min. max. min. max. max. MPa psi MPa psi MPa psi mm kg/m ENS-01 5 3/16 -3 4.6 5.4 10.6 11.6 15.1 16.7 14.1 41.5 83 165 90 0.32 ENS-02 6.3 1/4 -4 6.2 7.0 12.1 13.3 16.7 18.3 15.7 40 80 160 100 0.36 ENS-03 8 5/16 -5 7.7 8.5 13.7 14.9 18.3 19.9 17.3 35 70 140 115 0.45 ENS-04 10 3/8 -6 9.3 10.1 16.1 17.3 20.6 22.2 19.7 33 66 132 130 0.54 ENS-05 12.5 1/2 -8 12.3 13.5 19.0 20.6 23.8 25.4 23.0 27.5 55 110 180 0.68 ENS-06 16 5/8 -10 15.5 16.7 22.2 23.8 27.0 28.6 26.2 25 50 100 200 0.80 ENS-07 19 3/4 -12 18.6 19.8 26.2 27.8 31.0 32.6 30.1 21.5 43 85 240 0.94 ENS-08 25 1 -16 25.0 26.4 34.1 35.7 38.5 40.9 38.9 16.5 32.5 65 300 1.35 ENS-09 31.5 1-1/4 -20 31.4 33.0 43.3 45.7 49.2 52.4 49.5 12.5 25 50 420 2.15 ENS-10 38 1-1/2 -24 37.7 39.3 49.6 52.0 55.6 58.8 55.9 9 18 36 500 2.65 ENS-11 51 2 -32 50.4 52.0 62.3 64.7 68.2 71.4 68.6 8 16 32 630 3.42

EN 857 1SC Steel Wire Reinforced Hydraulic Rubber Hose

Introduction

EN 857 1SC hydraulic hose has similar performance with its counterpart SAE 100R1 besides tighter bending radius. It is reinforced by one-braid high tensile wire. Ozone and weather resistant cover separates the tube from the outside environment and effectively extends the service life of hydraulic hose. Single wire braided 1SC high pressure hydraulic hose is suitable for high pressure conditions where tight routing is required.

ENHH-05: EN 857 1SC hydraulic hose drawing.

ENHH-06: EN 857 1SC hydraulic hose.

Construction

• Tube: oil resistant synthetic rubber.
• Reinforcement: One-braid high tensile steel wire.
• Cover: abrasion and weather resistant synthetic rubber.
• Temperature: -40 °C to +100 °C (-40 °F to +212 °F).

Table 3: EN 857 1SC Steel Wire Reinforced Hydraulic Rubber Hose Technical Specification Item Size SAE Size I.D. Reinforcement W.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight mm inch dash min. max. min. max. max. MPa psi MPa psi MPa psi mm kg/m ENS-01 6.3 1/4 -4 6.1 6.9 9.6 10.8 13.5 22.5 45 90 75 0.20 ENS-02 8 5/16 -5 7.7 8.5 10.9 12.1 14.5 21.5 43 86 85 0.15 ENS-03 10 3/8 -6 9.3 10.1 12.7 14.5 16.9 18 36 72 90 0.19 ENS-04 12.5 1/2 -8 12.3 13.5 15.9 18.1 20.4 16 32 64 130 0.23 ENS-05 16 5/8 -10 15.5 16.7 19.8 21.0 23.0 13 26 52 150 0.29 ENS-06 19 3/4 -12 18.6 19.8 23.2 24.4 26.7 10.5 21 42 180 0.34 ENS-07 25 1 -16 25.0 26.4 30.7 31.9 34.9 8.8 17.6 35.2 230 0.49

EN 857 2SC Steel Wire Reinforced Hydraulic Rubber Hose

Introduction

EN 857 2SC hydraulic rubber hose serves high pressure hydraulic system where tight bends and maximum abrasion resistance performance is urgently needed. This type hydraulic hose owns oil resistant inner tube, which will not deform when transporting water based and petroleum based hydraulic fluids within -40 °C to +100 °C. The two-braid high tensile steel wires support high working pressure with tight bend radius. Chemicals and weather resistant cover guard long service life of the whole hose.

Plastic Well Casing Pipe - Pipe & Tubing

ENHH-07: EN 857 2SC hydraulic hose drawing.

Additional reading:
Category: Polyester mesh

For more information, please visit china two wire braided high pressure hydraulic hose.

ENHH-08: EN 857 2SC hydraulic hose.

Construction

• Tube: oil resistant synthetic rubber.
• Reinforcement: one-braid high tensile steel wires.
• Cover: abrasion and weather resistant synthetic rubber.
• Temperature: -40 °C to +100 °C (-40 °F to +212 °F).

Table 4: EN 857 2SC Steel Wire Reinforced Hydraulic Rubber Hose Technical Specification Item Size SAE Size I.D. Reinforcement W.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight mm inch dash min. max. min. max. max. MPa psi MPa psi MPa psi mm kg/m ENS-01 6.3 1/4 -4 6.1 6.9 10.6 11.7 14.2 40 80 160 75 0.30 ENS-02 8 5/16 -5 7.7 8.5 12.1 13.3 16.0 35 70 140 85 0.34 ENS-03 10 3/8 -6 9.3 10.1 14.4 15.6 18.3 33 66 132 90 0.42 ENS-04 12.5 1/2 -8 12.3 13.5 17.5 19.1 21.5 27.5 55 110 130 0.54 ENS-05 16 5/8 -10 15.5 16.7 20.5 22.3 24.7 25 50 100 170 0.68 ENS-06 19 3/4 -12 18.6 19.8 24.6 26.4 28.6 21.5 43 86 200 0.80 ENS-07 25 1 -16 25.0 26.4 32.5 34.3 36.6 16.5 33 66 250 1.15

EN 856 4SH Steel Wire Spiraled Hydraulic Rubber Hose

Introduction

EN 856 4SH steel wire spiraled hydraulic rubber hose consists of an inner tube of oil resistant synthetic rubber, four spiral layers of spiral wires reinforcement and is covered with oil and weather resistant synthetic rubber. Spiral hydraulic hose shares outstanding kick resistance, impulse resistance and can support surge pressure. EN 856 4SH hydraulic hose is widely used in applications where high pressure, high abrasion and kick resistance are urgently required. It is also be used in petroleum based hydraulic fluids within a temperature ranging from -40 °C to +100 °C.

ENHH-09: EN 856 4SH hydraulic hose drawing.

ENHH-10: EN 856 4SH hydraulic hose with four-spiral high tensile steel wire.

Construction

• Tube: high quality synthetic rubber compounds.
• Reinforcement: four-spiral high tensile steel wires.
• Cover: abrasion and weather resistant synthetic rubber.
• Temperature: -40 °C to +100 °C (-40 °F to +212 °F).

Table 5: EN 856 4SH Steel Wire Spiraled Hydraulic Rubber Hose Technical Specification Item Size SAE Size I.D. Reinforcement W.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight mm inch dash min. max. min. max. min. max. MPa psi MPa psi MPa psi mm kg/m ENS-01 19 3/4 -12 18.6 19.8 27.6 29.2 31.4 33.0 42 87 168 280 1.70 ENS-02 25 1 -16 25.0 26.4 34.4 36.0 37.5 39.9 38 76 152 340 2.50 ENS-03 31.5 1-1/4 -20 31.4 33.0 40.9 42.9 43.9 47.1 32.5 65 130 460 3.00 ENS-04 38 1-1/2 -24 37.7 39.3 49.8 49.8 51.9 55.1 29 58 116 560 3.60 ENS-05 51 2 -32 50.4 52.0 64.2 64.2 66.5 69.7 25 50 100 700 5.00

EN 856 4SP Steel Wire Spiraled Hydraulic Rubber Hose

Introduction

EN 856 4SP hydraulic rubber hose is similar to EN 856 4SH hydraulic hose, but the working pressure (under the same working temperature) is higher than EN 856 4SH hose. Four-spiral high tensile spiral wire reinforcement structure gives the hose best abrasion resistance and impulse fatigue. This kind of reinforcement is ideal for outdoor applications like forestry and mine equipment.

Oil resistant synthetic rubber is widely used in water and petroleum based hydraulic fluids within -40 °C to +100 °C. If the working temperature is lower or higher than the temperature, the service life of the hose will be changed.

ENHH-11: EN 856 4SP hydraulic hose drawing.

ENHH-12: EN 856 4SP hydraulic hose.

Construction

• Tube: high quality synthetic rubber compounds.
• Reinforcement: four-spiral high tensile steel wires.
• Cover: abrasion and weather resistant synthetic rubber.
• Temperature: -40 °C to +100 °C (-40 °F to +212 °F).

Table 6: EN 856 4SP Steel Wire Spiraled Hydraulic Rubber Hose Technical Specification Item Size SAE Size I.D. Reinforcement W.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight mm inch dash min. max. min. max. min. max. MPa psi MPa psi MPa psi mm kg/m ENSP-01 6.3 1/4 -4 6.2 7.0 14.1 15.3 17.1 18.7 45 90 180 150 0.64 ENSP-02 10 3/8 -6 9.3 10.1 16.9 18.1 20.6 22.2 44.5 89 178 180 0.75 ENSP-03 12.5 1/2 -8 12.3 13.5 19.4 21.0 23.8 25.4 41.5 83 166 230 0.89 ENSP-04 16 5/8 -10 15.5 16.7 23.0 24.6 27.4 29.0 35 70 140 250 1.10 ENSP-05 19 3/4 -12 18.6 19.8 27.4 29.0 31.4 33.0 35 70 140 300 1.50 ENSP-06 25 1 -16 25.0 26.4 34.5 36.1 38.5 40.9 28 56 112 340 2.00 ENSP-07 31.5 1-1/4 -20 31.4 33.0 45.0 47.0 49.2 52.4 21 42 84 460 3.00 ENSP-08 38 1-1/2 -24 37.7 39.3 51.4 53.4 55.6 58.8 18.5 37 74 560 3.40 ENSP-09 51 2 -32 50.4 52.0 64.3 66.3 68.2 71.4 16.5 33 66 660 4.35

Who Makes Quality Hydraulic Hoses Near Me

views

1

Liked

If you are looking for &#;hydraulic hoses made near me&#;, You've come to the right place. Here you can find out the best...

For more china four wire spiral high pressure hydraulic hoseinformation, please contact us. We will provide professional answers.

Read more